Kohler CV1000 Manual do Utilizador descarregar pdf (Página 36)

5.8

Section 5

Fuel System and Governor

Figure 5-11. Setting High Speed RPM (Air Cleaner

Removed for Clarity).

Carburetor Servicing

The following section covers the disassembly,

various servicing procedures and reassembly of the

carburetor. For each procedure carefully inspect

all components and replace those that are worn or

damaged. The following should also be noted as

Ĝȱȱȱǯ

• Inspect the carburetor body for cracks, holes, and

other wear or damage.

ȱ Ȋȱ ȱȱĚȱȱǰȱǰȱȱȱ

ȱȱĚȱǯȱȱȱĚȱȱȱ

Ğȱȱȱȱǯ

• Inspect the fuel inlet needle and seat for wear or

damage.

• The choke plate is spring loaded. Check to make

ȱȱȱ¢ȱȱȱĞǯ

Ǳȱ ȱȱȱȱȱȱę¡ȱȱȱ

ęȱȱȱȱȱȱǯȱ

Fixed jets for high altitudes are available.

Float Replacement

If symptoms described in the carburetor

ȱȱȱĚȱȱǰȱ

ȱȱȱȱȱȱȱȱȦ

ȱȱȱĚǯȱȱȱĚȱȱȱȱȱĚǰȱ

ǰȱĚȱǰȱǰȱȱǯ

1. Perform the removal procedures for the

appropriate air cleaner and the carburetor

ȱȱȱŞȱȃ¢ǯȄȱ

ȱ Řǯȱ ȱȱ¡ȱȱȱȱȱȱ

material before disassembling the carburetor.

Remove the four mounting screws and carefully

separate the fuel bowl from the carburetor. Do

ȱȱȱȱȱȱȬǯȱȱ

any remaining fuel into an approved container.

Save all parts. Fuel can also be drained prior to

ȱȱ¢ȱȦȱȱȱȱ

ȱǯȱȱȱśȬŗŘǯȱ

Figure 5-12. Fuel Bowl Removed From Carburetor.

ȱ řǯȱ ȱȱĚȱȱȱȱĞȱȱȱ

ȱĚǰȱȱȱȱǯȱȱȱśȬŗřǯȱ

Discard all of the parts. The seat for the inlet

needle is not serviceable, and should not be

removed.

Figure 5-13. Removing Float and Inlet Needle.

4. Clean the carburetor bowl and inlet seat areas as

required, before installing the new parts.

ȱ śǯȱ Ĵȱȱȱȱȱȱȱȱȱ

ȱĚȱȱȱȱǯȱȱȱşŖǚȱȱ

should point up, with the needle valve hanging

ǯȱȱȱśȬŗŚǯ

Move and Hold

Lever in "Full

Throttle" Position

High Speed (RPM)

Adjustment Screw

Fuel Bowl

Bowl Drain Screw

Float

Inlet

Needle

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 137 138

Comentários a estes Manuais

Sem comentários

Kohler CV1000 Manual do Utilizador Página 36

Comentários a estes Manuais

Manuais e produtos relacionados com Motor Kohler CV1000